What are the culture methods of Milan flower?
Milan is a highly appreciative flower variety, which has been widely concerned by people, so what are the breeding methods for Milan? I believe everyone would like to know the answer to this question, so next let's take a look at the cultivation methods of Milan flowers, and make us better apply them to our daily life through the study of the knowledge of Milan flowers. then let's take a look at the cultivation methods of Milan flowers.
Culture methods of Milan flower
Soil requirements:
Milan flowers prefer moist, fertile, loose loam or sandy loam, which is slightly acidic. The basin soil can be mixed with 25% compost, 50% rotten leaf soil and 25% river sand, and an appropriate amount of rotten cake fertilizer is put at the bottom of the basin as base fertilizer.
Lighting conditions:
Placing the Milan flower on a well-lit and well-ventilated garden or balcony with light for more than 8 to 12 hours a day will make the leaves of the plant green, the branches develop sturdily and bloom more often.
Temperature conditions:
The Milan flower likes to be warm, and the suitable temperature ranges from 20 ℃ to 35 ℃. It can blossom as many as 5 times from June to October. At the same time, in the plenty of sunlight, the flowers will be very fragrant.
Watering method:
Milan flowers like to be wet, watering should be determined according to the dry and wet climate, both to adhere to the basin soil moist and can not be long-term excessive moisture. In the period of dry weather and prosperous development, it is best to spray water on the leaves once or twice a day.
Proper fertilization:
Proper principles should be followed to stop fertilizing Milan flowers. After each blossom, fertilizers should be applied in real time after each blossom. Only in this way can Milan flowers blossom continuously and have rich aroma.
Culture methods of Milan flower
(1) adhere to the good performance of basin soil.
Milan has a well-developed root system, with many and thin beard roots. Therefore, it is necessary to timely replace the new soil rich in nutrients and eradicate the excess rotten fibrous roots. The basin should be changed at least once every two years, and those with good growth should be changed once a year. The new soil should be mixed with plant ash or burned-out cinder, and an appropriate amount of base fertilizer should be added to make the basin soil both fat and free of water, that is, breathable and nutritious. The extra fibrous root must be eradicated to make it send more new roots and enhance the absorption function of the root.
(2) apply fertilizer frequently by tapping water
When Milan starts to sprout in spring, it starts to buckle water. This is the most important part of "controlling branches and promoting flowers", so it is the peak period of Milan's germination, if it is not controlled in watering, it is bound to grow branches and leaves. Wait for its tender head to shrunk down slightly before watering.
Insist that the basin soil is always in a micro-dry state, which can control the development of nutrition and force it to transform into reproductive development. In this way, the development of branches and leaves can be gradually slowed down, and the leaves are thick, green and bright, the leaf spacing is short, the flower buds continue to differentiate, and the flowers and branches go hand in hand, and when the flowers bloom, the bouquet is even higher than the branches and buds.
Organic fertilizer was applied once or twice a week, and when the buds were scattered, the available phosphate fertilizer (potassium dihydrogen phosphate) was applied once. But also continue to buckle the right amount of water, to the tender head is not shrunken to the limit.
(3) adequate light should be provided.
This not only enhances the light and function of its leaves to produce more nutrients, but also produces short and stout branches, short leaf spacing, small and thick, green and bright leaves, promotes the continuous differentiation of flower buds, improves the quality and quantity of flowers, and produces flowers with rich fragrance, even in summer.
(4) picking the heart and thinning branches in real time
Milan has a strong germination rate and a large number of tillering buds and adventitious buds, so it is necessary to cut off the branches and leaves on the internal branches and the branches that are too dense, weak and long, so as to reduce the unnecessary consumption of nutrients. When the tender leaves grow to the fifth layer, they should pick their hearts and force them to produce more lateral branches. Controlling the length of each branch can not only make the plant shape perfect, but also make it blossom neatly and increase the number of flowering in each batch.
The culture method of Milan flower:
Milan flowers like sunshine, need fertilizer, participate in animal bones in the soil or wash rice water are conducive to Milan's flowering number and fragrance. Milan spend more time in blossom, and can be fattened once after each flower fade.
Milan likes warm, sunny places, which can be placed on the indoor windowsill, living room and study in winter, and can be planted in balconies or courtyards in other seasons.
Related
- Is the orchid suitable for indoor use? Is it good for the body?
- How to prevent the empty root of orchids?
- What to do after the crab claw orchid is withered?
- Why are the leaves of orchids always yellow? Fertilizing and watering.
- Can the root of the gentleman orchid be saved if it is rotten?
- Diagnosis and treatment of cotton-blowing beetle insects in Cymbidium
- There is a way for a gentleman's orchid to rot.
- What is the most suitable temperature and humidity for the orchid?
- How to raise a gentleman's orchid? Cultivation techniques of Cymbidium
- How to prepare the nutritive soil for the cultivation of Cymbidium