How does tiger skin orchid breed in spring?

The propagation of tiger skin orchid is mainly based on ramet propagation and cutting propagation.

The main results are as follows: (1) in ramet breeding families, it is best to change pots in early spring. The underground part of tiger skin orchid is a creeping rhizome, and many small buds sprout in the stem node of the rhizome every spring, making the plant grow more and more full. For the crowded plants, remove the roots carefully and plant about 3-4 leaves in each clump. The basin soil should not be too wet, otherwise the rhizome wound is prone to infection and decay.

(2) there is no obvious stem in the aboveground part of cuttage, and the cuttage is mainly leaf cuttage, which is a typical material with high survival rate of leaves. The cutting should be carried out from May to June. The robust leaves on the periphery of the plant were selected and cut into 5 cm long leaf segments, and then the cuttings were dried under scattered light for about 1 hour to make the incision contract and heal properly and prevent the substrate from rotting. Finally, the cuttings are obliquely inserted in the sand bed, paying attention to the upper end facing up and the lower end facing down. in order to avoid confusion, the cuttings can be distinguished by different cuts. Proper shading and moisturizing after insertion can take root after 4 weeks, and the survival rate is higher. In another 2-3 weeks, adventitious buds will grow in the lower incision, and when the new buds are 10 cm out of the sand, they can be planted in small flowerpots.

Tiger Pilan Phnom Penh series varieties are not suitable to be propagated by leaf cutting, otherwise, Phnom Penh will disappear and reduce the ornamental quality. Seedling transplanting, should not be too much watering, such as high temperature and humidity is easy to cause rhizome rot. With a little shade in summer, the leaves are fresh green and tender, and the same year can become full potted flowers.

How to propagate the tiger tail orchid, the propagation method / ramet of the tiger tail orchid is the most applicable.

Tiger tail orchid is famous for its green leaves and tiger markings. Its maintenance and management is mainly extensive, and it is relatively easy to breed. This involves the problem of reproduction. When the tiger tail orchid is raised to a certain time, it needs to be reproduced, so how to reproduce? Let's take a look at the breeding method of tiger tail orchid.

How does tiger tail orchid reproduce?

In general, there are three common ways of propagation, namely, ramet, cutting and sowing. For most potted flower lovers, ramet and cuttage are the most practical, and sowing is actually very simple. Let's introduce these methods in detail below.

1. Cuttage propagation of Cymbidium

1. Applicable varieties

Because there are many species of tiger tail orchid, and many of them have golden edges or silver veins, there will be yellow and white markings on them, these varieties are not suitable for cutting, although cutting is the most commonly used breeding method of tiger tail orchid, but because it will cause these markings to disappear, it is only suitable for ordinary species of tiger tail orchid.

2. Cutting method

⑴, select leaves from strong plants, cut them into segments 5-6 cm long, place them in a cool place and wait for the incision to dry naturally.

⑵, use sand and vermiculite as the substrate into the flowerpot, insert the dried leaves directly or obliquely into the substrate, the depth is usually 1/2 or 1/3 of the cut, and then water thoroughly.

⑶, keep the soil moist, the temperature is between 15-20 degrees, it can take root in a month, it will take root from the base and grow into a rhizome, and then slowly grow into a new plant, and then wait until there are 2-3 new leaves can be transplanted.

Second, how to split the tiger tail orchid

1. Applicable varieties

Because the ramet is planted separately after dividing the mother plant, it is one of the propagation methods of Cymbidium, which has little effect on plant growth, and can be applied to any species of Cymbidium. The most suitable breeding time is in spring and summer. It can be carried out together with changing pots in spring.

2. Ramet method

⑴, how to propagate tiger tail orchid when using ramet? First of all, the mother plant should be removed from the flowerpot, and the mother plant should be divided into several clusters with a knife, and the root injury should be avoided as far as possible in the process of separation, and each daughter plant needs to retain more roots.

⑵, smear the cut with plant ash and then dry it, then plant it in a new pot soil, plant it in a cool place, water it as little as possible, prevent the root incision from rotting, and keep the environment moist and wait for new leaves to grow.

Third, how to sow the cymbidium

Buy fine seeds from the professional flower market, then sow them evenly in fertile soil, water thoroughly and keep the temperature at 20-25 degrees. After waiting for a period of time, they can send out buds, and when they grow leaves, then carry out normal maintenance in accordance with the breeding methods of Cymbidium.

How to propagate Magnolia paniculata

Propagation: commonly used ramet and cuttage propagation. Ramets were carried out during the basin change from March to April in spring. The crowded plant clusters growing along the edge of the pot were plucked off with rhizomes, and after the stem injury □ was slightly dried, the plants were potted directly. Cuttings are often carried out from May to June, and leaves of moderate size are selected as cuttings. Cut into 7 Mel 8 cm long, inserted in the sand bed, rooting about 1 month after insertion, and can be potted when the root length is 2 mi 3 cm.

Cultivation: like warm, dry and sunny environment. Not resistant to cold, more resistant to shade but afraid of waterlogging. The soil should be rich, loose and well drained sandy loam. The winter temperature is not lower than lO degrees Celsius.

Just potted seedlings, not too much watering, slightly dry is better. After the new leaves are exposed to the soil, the oysters can keep the soil slightly moist. Fertilize once a month during the growing period. When it is hot and bright in summer, it can be shaded and sprayed with water on the leaf surface. The flowering period from July to August can be watered more. Move indoor maintenance in winter. The broad-leaf tiger tail orchid has a large shape and irregular rhizome growth, so it is necessary to prune and adjust the plant shape or renew it in time when potted every year.

Diseases and insect pests: common gray gangrenous disease and brown spot disease can be sprayed with 70% methyl topiramate wettable powder lOOO double liquid. Insect pests are harmful to weevil, so 20% fenvalerate 25OO solution is used to kill.