The cutting method of Prunus mume is illustrated and the detailed cutting method is shared.

For the cutting method of Bougainvillea, many flower friends prefer to see the cutting method diagram of Bougainvillea, which is not only intuitive, but also imitative, flower friends are easier to use, the following wed114 small series will bring you the details of the cutting method of Bougainvillea, sorted out for flower friends to refer to, together to see the details.

1, prepared cutting substrate. (vermiculite, pearlite, peat, 1:1:1. Sand, plain sandy loam, etc. can also be used)

2, at the bottom of the thin pad a little elastic wadding.

3. Install the matrix and blanch it with boiling water several times, cool it and set it aside.

4. Cut the sunny branches as cuttings, and it is better to bring some old branches with new branches. After June, new branches that have been semi-lignified do not need to bring old branches.# p#subtitle #e#

5, cut cuttings, old branches should be thick, there are new branches with leaves.

6. Cut off the cuttings with a sharp knife, leaving two half leaves for the big leaves, two leaves and one bud for the small leaves, about 7-10cm long, cut off the base of the branches, cut the mouth uneven, damage the tissue, cut off the damaged tissue with a sharp knife, and cut the base into an inclined plane with a knife. Below is a picture of the tidied branches.

7. Prepare the rooting powder according to the instructions and soak the cuttings at the base.

8, with a clean (sterile) stick oblique insertion hole, 7-8cm deep, and then buried cuttings, exposing the leaves of the node.# p#subtitle #e#

9, insert a pot, pour some cold boiled water or bottled water, so that the substrate and the base of the cuttings are in close contact, conditional can be outside the pot, convenient management.

10. Cover with plastic wrap to keep moisture. There are ventilation holes on it, and there is sparse sunlight to cure it.

11. The seedlings have survived in the middle of June and are planted separately in pots.

The method of cutting propagation of triangular plum is illustrated by the method of pruning triangular plum.

Bougainvillea flowering long, properly cultivated throughout the year can bloom, so many friends like to use bougainvillea potted decoration home. How does the triangle plum reproduce? How to trim it? Next Xiaoqi will share the cutting method of Bougainvillea chinensis and the pruning method of Bougainvillea chinensis.

1. Cutting method of triangular plum

One-step cuttage method: cutting directly to the pot, so that it takes root in the pot long branches, as soon as possible, to achieve the year cuttage, the initial formation of the ornamental effect.

1. Branches: From March to April, select perennial branches with a diameter of 1--1.5cm or more, and cut them at a height of 20~30 cm from the ground. The thicker the diameter of the selected branches, the better. The varieties of single petal red towel, single petal red towel and single petal purple towel were better.

2, the treatment of branches: with saws will be 18~22 cm long branches for a section (each section with at least 3 buds) saw, with box storage, placed in the rain less than the shade, after 10 days or so, cutting branches of the epidermis slightly wrinkled, they began cutting.

3. Upper pot planting: The planting substrate can be mixed with pond mud, wood chaff, garbage fertilizer or decomposed bagasse, the ratio is 6:4, 1~3 branches per pot, placed in the shade shed, drenched with water. After one month, it can sprout, grow roots and become new plants.

4, management measures: timely weeding, loose soil, drainage of water work, in order to improve the survival rate. After lignification of new shoots, pruning should be done in time to promote more new shoots to germinate, which is beneficial to early formation of good crown.

Second, the triangular plum pruning method

Heavy pruning: From the name, you know that this pruning must be very large. You need to cut off all the branches basically, leaving only stumps and a few main branches. The remaining main branches should also be cut very short. In particular, unnecessary branches should be completely cut off.

Medium shear: naturally, it is lighter than heavy shear, just cut off some dead branches and unwanted branches, cut short the parts that grow well, and the whole tree does not change too much.

Light pruning: Cut short some weak branches, sick branches, and healthy branches. Generally used on seedlings, seedlings and small trees. In order to make good use of photosynthesis, let seedlings grow quickly.

Retraction: Cut all branches short so that this year's tree is not much different from last spring's tree. The purpose of retraction is to make enough space and room for plants to grow.

The above is the method of cutting and pruning of Bougainvillea triangularis shared, I hope to help everyone cultivate Bougainvillea triangularis, the pruning of Bougainvillea triangularis more beautiful.

The cutting method of triangular plum (diagram)

Cuttings of Bougainvillea angustifolia: soil treatment

First of all, prepare a good cutting matrix. (vermiculite, pearlite, peat, 1:1:1. Sand, plain sandy loam, etc. can also be used)

Add a small amount of slag to the culture soil, sift the slag before cuttage, select particles of about 2 to 5 mm, soak in boiling water, and disinfect. Dry in controlled water until no dripping occurs and mix thoroughly for later use.

Cutting of Bougainvillea: Preparing the Flower Pot

Need cuttage many pots can use simple plastic pot, cuttage success after the pot. After selecting the flower pot, you need to fill the soil. At the bottom of the flower pot, a thin pad of elastic wadding is needed.

After the soil is prepared, water it thoroughly, put it in the sun, and dry it for later use.

Cutting of Bougainvillea: pruning

Cut the sunny branches for cuttings, and it is best to bring some old branches with the new branches. After June, new branches that have been semi-lignified do not need to bring old branches.

Cut cuttings, old branches should be thick, there are new branches with leaves.

Cut off the cuttings with a sharp knife, leaving two half leaves for the big leaves, two leaves and one bud for the small leaves, about 7-10cm long, cut off the base of the branches, cut the mouth uneven, and the tissue is damaged. Cut off the damaged tissue with a sharp knife, and cut the base into an inclined plane with a knife. Below is a picture of the tidied branches.

Trigonum bougainvillea cuttings: soaking branches

The rooting powder is prepared according to the requirements of the instruction manual, and the cutting base is soaked.

Trigonometry of cuttings: cuttings

Use a clean (sterile) stick to insert holes obliquely, 7-8cm deep, and then bury the cuttings to expose the nodes that remain leaves.

Insert a pot, pour some cold boiled water or bottled water, so that the substrate and the base of the cuttings are in close contact, conditional can be outside the pot, convenient management.

Cover with plastic wrap to keep moisture. There are ventilation holes on it, and there is sparse sunlight to cure it.

In mid-June, seedlings have survived and are planted separately in pots.