Why is the big paulownia rotten ball? what to do if the big rock tree rotten ball / dig the ball, cut and rot and replant

As a common indoor farmed flower, paulownia flower friends should be no stranger, its leaves are large and green, the flowers are beautiful and colorful, and they are very ornamental indoors. But in the process of breeding, many flower friends will encounter the phenomenon of rotten balls, so why is the big paulownia rotten? What if the big paulownia rotten ball? Today, the editor is here to solve this problem for everyone.

First, why the big paulownia rotten ball, soil discomfort / improper watering

Although the breeding method of paulownia flower is not difficult, it is a kind of plant that is easy to rot ball, which often gives flower friends a headache, and they all want to know why it is rotten ball. In this regard, after the editor's inquiry, in fact, the reason is very simple, in the case of poor soil drainage or improper watering, the tree will rot. As for the big rock tree rotten ball what to do, let's move on.

Second, what to do when the big paulownia rotten ball? dig the ball, cut it, rot and replant it.

After finding the rotten ball, do not rush to deal with it, first observe the soft and hard degree of the bulb. If the big paulownia bulb is soft, don't think about it, throw it away, it's hopeless! But if the bulb is hard, it can be saved. As long as we do the following 5 steps, the big rock tree can sprout and grow again.

1. Dig out the bulb

Dig out the rotten corm of the tree tree and wash it clean. In the process of cleaning, the rotten roots can be removed directly.

2. Cut off the rot

Take the cleaned bulbs in one hand and cut off all the rotten parts of the bulbs in the other until you see the healthy parts. The purpose of this is to avoid the spread of corm infection.

3. Air drying and disinfection

After the bulb is treated, put it in the sun to dry. Generally, it takes about 1 hour to dry the bulb wound, which can not only dry the bulb wound, but also keep the bulb from dehydration. Then smear carbendazim on the bulb to achieve disinfection effect.

4. Replant

Prepare clean sterile soil, vermiculite, perlite or river sand, but it is best to use water moss (which can be twisted to dry and control humidity), then replant the sterilized paulownia bulb and finally close it up in a transparent container.

Note: in the process of planting, only half of the bulbs should be planted, and the wound should not be stained with soil. In addition, the humidity of the air in the container should not be too high, do not appear water droplets, because there are wounds, too wet and easy to rot.

5. Waiting for germination

After the big paulownia bulb is planted, it will begin to sprout after waiting for about 1-2 weeks. After that, we need to clean up the water moss in time and try not to break the roots. Then bury it with the soil, and after doing so, the big rock tree that has rotted the ball will rejuvenate its second spring.

What should I do if the big paulownia rotten ball?

Big paulownia rotten ball

Paulownia is relatively rotten, in breeding, poor soil drainage or improper watering, may lead to its rotten ball, must be disposed of.

When the big paulownia rotten ball, first need to try whether the bulb is hard or soft, if the bulb has become soft, it is best to throw it away. However, if the bulb is still hard, it can be treated and can sprout and grow again.

What should I do if the big paulownia rotten ball?

The first step is to dig out the rotten ball, then wash it clean, remove the rotten root system first, and pay attention to pulling it off directly.

The second step is to use a sharp knife to cut off the rotten part of the bulb until the healthy part of the ball appears, so as to prevent the corm from spreading and continue to rot.

The third step is to cut off the rotten bulbs and put them under the sun to dry. It usually takes about an hour to dry the wound, but be careful not to let the bulbs get dehydrated.

The fourth step, put carbendazim on the bulb for disinfection.

The fifth step is to replant the processed bulbs, first of all, you need a real quilt medium, you can prepare clean water moss or vermiculite, river sand, etc., but it is better to use water moss, which can twist dry and control humidity.

Step 6, bury the bulb with prepared water moss or soil, half of it, and be careful not to bury the wound. Then use a transparent container to suffocate it, pay attention to the humidity of the air in the container is not too high, otherwise it is easy to rot.

Then, after about a week or two, it will begin to sprout.

After the bulb sprouts, if it is raised with water moss, the water moss needs to be cleaned up in time, but be careful not to hurt the bulb. And then bury it with soil.

How to teach you how to save the tree tree in six steps?

Paulownia is a common family flower culture, but sometimes there will be rotten balls, which is more worrying. Next, let's take a look at what to do when the big rock tree rotten ball.

Big rock tree rotten ball:

Paulownia is relatively rotten, in breeding, poor soil drainage or improper watering, may lead to its rotten ball, must be disposed of.

When the big paulownia rotten ball, first need to try whether the bulb is hard or soft, if the bulb has become soft, it is best to throw it away. However, if the bulb is still hard, it can be treated and can sprout and grow again.

What should I do if the big Yantong rotten ball?

The first step is to dig out the rotten ball, then wash it clean, remove the rotten root system first, and pay attention to pulling it off directly.

The second step is to use a sharp knife to cut off the rotten part of the bulb until the healthy part of the ball appears, so as to prevent the corm from spreading and continue to rot.

The third step is to cut off the rotten bulbs and put them under the sun to dry. It usually takes about an hour to dry the wound, but be careful not to let the bulbs get dehydrated.

The fourth step, put carbendazim on the bulb for disinfection.

The fifth step is to replant the processed bulbs, first of all, you need a real quilt medium, you can prepare clean water moss or vermiculite, river sand, etc., but it is better to use water moss, which can twist dry and control humidity.

Step 6, bury the bulb with prepared water moss or soil, half of it, and be careful not to bury the wound. Then use a transparent container to suffocate it, pay attention to the humidity of the air in the container is not too high, otherwise it is easy to rot.

Then, after about a week or two, it will begin to sprout.

After the bulb sprouts, if it is raised with water moss, the water moss needs to be cleaned up in time, but be careful not to hurt the bulb. And then bury it with soil.