How to make moss bonsai

raw materials

Moss, flowerpots, sticky soil.

step

1. Prepare moss.

Moss sources show more, especially in some damp places, as long as the blade, gently scrape a part of it, if there is no moss near the city residents, you can go to the market to buy some moss.

2. adding soil to flowerpots

First put the bottom of the flowerpot on breathable muck or some gravel pieces, then put it into sticky soil to compact, then water it, and then start to dilute the mud. After having a certain viscosity, filter out the excess water.

3. moss spreading

Spread moss remember to be higher in the middle and lower around, which is good for drainage. If the moss is too large, we can tear it into small pieces and make sure that the whole flowerpot is covered.

4. Embellishment

After spreading moss, you can add some embellishments, such as placing small stones beside them, or planting other green plants on top of the pot, which can make the pot look gloomy.

In this way four small steps, we can make the moss potted plant, after the production also pay attention to maintenance, we also come to understand the maintenance method.

How do mosses grow? How to make moss bonsai?

Introduction: There are many kinds of moss plants, many of which can be planted and appreciated. It is also very wonderful to make bonsai culture. Many flower friends are interested in this small plant. The first agricultural classic series below introduces you to the production method of moss bonsai and the maintenance points of moss plants.

The method and steps of making moss bonsai are as follows:

1. Look for moss. There are many kinds of moss suitable for decorating potted plants, but the most important thing is that Tess is not too long. There are also many channels to obtain moss, some friends buy from the Internet, indicating that they are too rich, I calculated that the general 30cm pot surface will cost nearly 50 yuan, our common people's practice is to find suitable plants on the ground, stones or trunks in the shady tide of the mountains. Of course, if you are a large and medium-sized city, it is difficult to do, then your easiest way is to go to some years of brick-concrete roof solar panels below, next to the drainage holes, tile surface of tile houses, outdoor drainage to find.

2. Collect moss. Gently scrape the whole piece along the bottom with a blade or bamboo stick.

3. Prepare some fine soil, which should be sticky, and remove large particles.

4. Clean up the basin surface. Use a knife or bamboo stick to hang off the rough layer of the basin surface.

5. Clean up moss. Gently clean up the large and fast wood residue rotten leaves at the bottom of the moss (do not clean up if there is no one, because the collection channels are different, so some do not).

6, basin surface preparation. After the bonsai is watered thoroughly, a layer of fine soil is evenly sprinkled on the surface of the pot, generally no more than 1cm, and then the fine soil is watered and gently stirred into a thin mud.

7. Spread moss. The shape of each moss piece can be determined by gently tearing off the edges or using scissors according to the shape of the basin surface and the pattern you want to arrange.

8) Management in the future. Put the prepared bonsai moss in the shade of the courtyard or in a cool and ventilated place at home. Spray water with a watering can every 1-2 days to keep the moss moist (it is important to keep it moist, otherwise the son will become dry). Slowly, the moss will survive.

Moss Bonsai Conservation Notes:

The environment suitable for moss growth is very similar to the environment suitable for human habitation: maintain a certain humidity, ventilation, moderate lighting.

2, bryophytes are not suitable for growth in the dark, it needs a certain amount of scattered light or semi-shade environment. During curing, a certain amount of light should be given, preferably weak scattered light rather than direct strong sunlight.

3, spray water many times a day, do not pour too much water at a time, keep the moss wet. The best growth temperature of moss jade is about 25℃, and it should be placed indoors in winter.

Moss is very different from other plants. One is that its roots basically only play the role of climbing fixed plants, mainly relying on leaves to absorb water and meager nutrients in the air. Second, if the air humidity is not enough, it will automatically enter a dormant state. The color turns greyish green, but that doesn't mean the moss is "dead." In fact, mosses that go dormant are robust, resistant to heat and cold, can last for months, and turn green when exposed to moisture.

What is moss bonsai moss bonsai should be made

For moss, I believe many friends will not feel strange to it. Mosses are known as the lowest higher plants, which are widely distributed all over the world. They are small green plants with no flowers and no seeds. But how much do you know about Moss Bonsai? How should moss bonsai be made? The following small series will briefly introduce it to friends.

What is moss bonsai?

Bonsai, is a plant and rocks as the main basis for the production of materials in the pot can be made of natural landscape works of art. And the moss bonsai, can not understand. Moss bonsai is a work of art made of moss as the main plant and rock materials.

How should moss bonsai be made?

Moss bonsai is a green, very expressive art, it is precisely because of this, moss bonsai has become one of the most popular bonsai art. Moss bonsai production methods and steps are mainly:

I. Preparations.

Before making moss bonsai, you need to make sufficient preparations, and the materials for making bonsai are ready. Specific materials are mainly flowerpots or other potted plant production containers, rocks, culture medium soil, watering cans, moss, moss and other materials.

2. Making bonsai base stone.

Making bonsai bottom stone is to pour small particles of rocks into flower pots, generally pour a thin layer of rocks, its biggest role is to play a role in water separation.

3. Laying moss.

The purpose of laying moss is to prevent the upper moss from entering the bottom stone after planting, which affects the beauty of the potted plant. Specifically, the moss is soaked in water, squeezed dry and laid in the flowerpot.

4. Making bonsai modeling.

Making a bonsai is to put the prepared rocks into the flowerpot according to the shape of the moss bonsai to be made. Then use a watering can to spray appropriate water to keep rocks and moss moist.

5. Pour into the culture medium soil

Pouring the culture medium soil is to pour the prepared culture medium soil into the flowerpot according to the shape of the moss bonsai. It must be said that the base soil needs to be moistened before pouring it into the pot.

VI. Laying moss

Laying moss is a key step in making moss bonsai. Specifically, the surface impurities of moss are cleaned up first, and water is sprayed on it to make its roots and surface wet, and then moss is laid on the surface of medium soil and compacted.

In addition, after the moss is laid, background plants or decorations can be planted as needed. Finally, it is necessary to pay attention to the watering of moss bonsai, which will keep it green for a long time.