How to accelerate bud of Lentinus edodes with bag material?

How do bag mushrooms bud? What do you need to pay attention to when mushroom buds? Also ask experienced netizens to help introduce The method of injecting water or soaking bag to promote mushroom in bag culture will make the water content in mushroom stick too high; some mushrooms will not produce for a long time after promotion, miss the cultivation season of mushroom, and affect the yield, quality and benefit. Land network sorted out six kinds of bag material mushroom bud method, the following list for netizens reference. Method 1. Directional piercing method: With 8-10 cm long nails 4, nail in the thickness of 1.5 cm, length of 45 cm, width suitable for hand grip on the board, nails to all nail into. Prick two rows of seeds arranged on the mushroom rod with nails, and 8 eyes are arranged in two rows on one side. Method 2: Vertical bag swing method: Put the perforated rods vertically into a dip tank or vat, up to 2 layers. The top is pressed with bamboo rafts, and then heavy objects such as stones are pressed to prevent the bacteria rod from floating. Method 3: Blending liquid for bud induction: Prepare 0.3% urea solution in a quantitative water bucket or pool, inject the prepared solution into the pool where the bacteria stick is placed, immerse the bacteria stick for 5- 10cm, and maintain the water level for 1 hour. Method IV: Dip the bag regularly: Immerse the bacteria stick in water for 1.5-3 hours. Among them, the spring tide mushroom is immersed in water for 1.5-2 hours; after the second tide, it is immersed in bags for 2-3 hours each time. After soaking for 1.5 hours, the sampling of soaking water content was started, and the water content around the nail hole was 65%-70%, and the other parts were 45%-60%. The bacteria rod showed partial water content and partial water content. Generally, the weight method is used to determine the soaking amount. The weight after the first soaking is 100%-110% of the weight of the bacterial rod cultivation, and the weight of the spring planting bag is about 90%-105% of the weight of the cultivation. After that, the weight of immersion water decreased by about 15% per tide. Method V: Use temperature difference to promote bud: Select the day and night temperature of 8℃-20℃ to soak bags for mushroom promotion, the night must appear below 12℃ low temperature, moderate temperature strains need 14℃-16℃ low temperature. A linear drainage hole is pricked at one end of the bacteria stick soaked in water, the drainage hole end is downward, discharged on the sunny leeward ground without ponding, covered tightly with a plastic film, and a thermometer is placed on the bacteria stick in the film. Sunlight irradiation, sunlight temperature lower than 15℃ or cloudy days, can increase the temperature, promote the temperature under the film to reach 28℃-32℃, keep 2-4 hours, lift the film ventilation, and then use the natural low temperature at night about 12℃ stimulation for 4-6 hours. As long as the temperature control is accurate, once can be. If the temperature is insufficient, it can be carried out 2-3 times in a row. Method VI. Method of regulating temperature for budding: The bacteria rod stimulated by puncture, immersion and temperature difference can be fixed in place, covered with plastic film tightly, and compacted around. Under the condition of 18℃-24℃, the mushroom bag produces a large number of mushroom buds after 2-3 days. Generally, from the evening of the next day or the morning of the third day, select the mushroom sticks with more buds and put them into the lowest layer of the mushroom shed. After that, one batch is selected every 12-24 hours, put into the mushroom shed from bottom to top, and complete in 2-3 days. Notes for mushroom bud promotion: Note 1. The water content of the mushroom rod promoted by the above method should be 35%-55%. For the bacterial rods with water content lower than 35%, a small amount of water should be added in advance; for the bacterial rods with water content higher than 55%, the soaking time should be shortened appropriately or not soaked. Note 2, temperature difference bud warming process, should be checked once every 30 minutes. If it exceeds 35℃, it should be cooled immediately. Mushroom inoculation method Mushroom does not produce mushroom reasons Click to get more mushroom cultivation technology Click to get more edible mushroom cultivation technology