Water plants make trees? After reading it, I just want to say 666.

Recently, everyone has been asking, how to do the small cylinder Moss landscape? Is Moss easy to live? What kind of help to fish friends. Today, the editor will teach you all the background methods of making Moss balls, Moss walls, Moss trees and even grass jars with MOSS. Let's have a look!

Moss's advantages

As we all know, the main use of aquatic MOSS is to create a natural aquarium landscape by attaching it to sunken wood or stone. It is not very difficult for Moss to plant in the aquarium. They can tolerate low light, grow well without carbon dioxide supplementation, and can survive on very small amounts of nutrients. As an epiphyte, the false root of MOSS can be fixed to mesh, wood and stone to make a variety of landscaping. Not only that, MOSS is also very important for fish reproduction, because aquatic MOSS can be widely used as egg beds, while MOSS can also absorb excess waste produced by fish fry.

Moss ball production

Open the sunken wood landscape tank, the rest of the Moss, it is a pity to throw it away. I tried to make a few Moss balls, and it felt good.

1. Preparation materials: mousse, biochemical ball, bath flower, glass ring, fishing line, foam, scissors.

two。 Open the biochemical ball, take out the biochemical cotton inside, take a small piece of foam (the purpose is to make the mosaic ball can be suspended in the water, because the internal space of the biochemical ball is small, the foam is not too large) into the biochemical ball, and then buckle the biochemical ball.

3. Take a small amount of mousse and evenly lay it on the surface of the biochemical ball, not too thick, a thin layer. This step can be done with the help of "Moss instant glue" to help secure Moss more firmly to the surface of the biochemical ball. Note: the colloid is white after solidification, please pay attention to the dosage when using it, if you stick to the mousse, you only need a little bit, if you use more, you will see the white glue spot on the front, which will affect the appearance.

4. Take a small piece of bath flower and carefully wrap the biochemical ball covered with Moss, not too tightly, so as to facilitate the germination of new buds of Moss.

5. Tie up the opening of the bath flower wrapped in Moss with a fishing line, then cut off the excess bath flower, leaving the 30CM around the fishing line for backup.

6. According to the height at which the moose ball floats in the cylinder, tie a glass ring to the end of the fishing line (to fix the moose ball).

7. According to your personal preference, put the mousse ball in the appropriate position in the cylinder, and the glass ring can be embedded in the bottom sand.

The making of the Moss Wall

Preparation: 1. Triangular mousse or any kind of mousse. 2. 2mm eye stainless steel mesh (1 foot X 3 feet). 3. A small sucker. 4. Dark cotton thread / juvenile fillet. 5. Sharp-tip camera, small scissors.

Triangle mousse, not too much, broken can be used. To form a triangle, it is best to stick to the object, the water temperature should not exceed 28 degrees, if it is more than 28 degrees, it will be easy to grow young and yellow, lighting and CO2 requirements, and positive grass, too dark but not good.

After buying the stainless steel net, cut out the required size with small scissors, and then remember to clean the steel net with hot water and detergent, because there is a lot of oil.

First, make the triangle moss into strips to facilitate the arrangement. Then use the camera to line up the strips one by one on the Internet, and put a few more mousses on the Internet. Moss does not have to line up too thick, because after tied up, there will be no light below and will not grow well, and Moss can grow new buds anywhere, the more gaps, the denser it will be.

After arranging the mousse, you can tie it with cotton thread, tie a knot and fix it in one corner of the steel net, then make an oblique winding to the other side along the steel net, then come back diagonally from the other side, and then tie the knot to fix it, then the cotton thread will form a grid on the Internet, and the Moss will be posted on the Internet and will not fall.

Basically, the mousse piece has been completed and can be placed at the bottom of the cylinder. However, if you use triangular mousse, because it will grow into layers, such as at the bottom, it is better to use ordinary / Java / wicker mousse.

If triangular mousse is used, it can be affixed to the cylinder wall to form a row of mosaic walls. In the finished triangle moth piece, cut a small gap, plug the small sucker into it, and stick it on the cylinder wall.

Six methods of Morse Tree

Method 1 steel wire ball fixation

First of all, prepare a steel wire ball, which is sold in the supermarket.

The rhododendron root tied down the stone so as not to float up

Fixed steel wire ball

Bind Moss.

Method 2. Biochemical cotton method

Black biochemical cotton method: it is the same as the practice of steel wire ball, except that the matrix is the kind of coarse porous black biochemical cotton used in filtration. After cutting it into a hemispherical shape, the other methods are the same as those of steel balls.

Method 3. Metal mesh screws are fixed

The mesh is fixed and can be made of stainless steel mesh or aluminum mesh without rust.

Method 4 processing and molding mesh is fixed

On the basis of the third part, the net is modeled at a price and lent out the angle.

Method 5. Plastic sheet fixation

Method 6 directly bind

The premise is that sunken wood or rhododendron root should have a crown shape, which can be strengthened and fixed with mousse instant glue to replace the annoyance of binding.

There are surprises here.

Game fans: use the straw jar to restore the game scene perfectly!