MySheen

Propagation methods of rubber trees

Published: 2024-11-22 Author: mysheen
Last Updated: 2024/11/22, Rubber tree is a very famous potted foliage plant, which is very common in the central cities in the north, and there are many varieties of rubber tree, among which Venus broad-leaf rubber tree is an excellent variety of rubber tree. So how do rubber trees reproduce? The editor will introduce you.

Rubber tree is a very famous potted foliage plant, which is very common in the central cities in the north, and there are many varieties of rubber tree, among which Venus broad-leaf rubber tree is an excellent variety of rubber tree. So how do rubber trees reproduce? The editor will introduce you.

Rubber tree

Family cultivation is generally propagated by cutting and high branch pressing, and the Yangtze River Basin is the most suitable from April to September every year. If cutting is carried out in spring and summer, the robust branches in the upper or middle of the plant should be selected as cuttings. When cutting in autumn, the sturdy new branches of the same year should be selected as cuttings. The specific steps are as follows: cut off the branches to be cuttings, remove the top shoot and the lower leaves, leave the middle leaves, and cut off the leaves 1 / 2, in order to reduce the evaporation of the leaves, it is best to roll the leaves into a barrel, and use a small stick to pass through the reel and insert it into the soil to prevent cuttings from lodging. In addition, cut cuttings should immediately seal the upper and lower incisions with plant ash or peat soil to prevent excessive milk overflow and reduce the survival rate. The depth of cutting is generally 3cm-4cm, if it is too deep, it will rot, and if it is too shallow, it is easy to lodge. The substrate of cutting is generally made of fine sand. Keep the sand moist after planting, and put it in the shade to see scattered light. Be careful not to get caught in the rain. Cuttings can usually take root after a month. When planting seedlings, we should try to be careful not to shake the matrix around the new roots, so as not to hurt the roots and affect the growth after planting. In the family, the use of high branch pressing method is more convenient, and the success rate is also high. The method is as follows: select the biennial branches, first peel the branches with a wide 1cm-1.5cm ring, then wrap the wound with wet moss and peat soil, wrap the upper and lower ends with plastic film, press the strips in June, and cut off the potted plants after rooting from July to August.

Culture methods of rubber trees

Rubber tree is an evergreen shrub plant, native to India and Malaysia. It is also cultivated in many places in China. The leaves of rubber trees are large and shiny, the leaves are long oval or round, the leaves of rubber trees are dark green, and the back is light green.

Culture methods of rubber trees

1. The rubber tree is high-temperature and humid, sunny, moisture-resistant and cold-resistant. It grows quickly in a high-temperature and humid environment to ensure adequate fertilizer and moisture. It can grow a leaf from 5 to 10 days. Fertilization should be appropriate, once or twice a month.

2. In the strong sunshine environment, the growth is very good, although I like the strong sunshine very much, the light at the bottom of the room can also grow very well, in order to promote the growth of the seedlings when they grow to 50-80 cm, let the side branches germinate, they can pick out the heart and let the flowers and trees form evenly.

3. Rubber trees can be propagated by cutting and high branches, and the simple and easy way to survive is cutting. This method survives well and grows fast, usually in late spring and early summer when pruning flowers and trees.

4. High-pressure cutting is also very convenient. In the family, select 2-year-old branches, plant them in rings with a width of 1-1.5 inches above the branches, and wrap them with moist soil. After 1-2 months, the branches can take root and cut off for cultivation.

5, the rubber tree ornamental performance is very good, the leaf is broad and beautiful, when we like the pot ornamental plant, put in the living room study is a very tasteful ornamental plant, will bring you a very interesting tropical scenery.

Propagation methods of rubber trees

The rubber tree is of high ornamental value and is a famous potted foliage plant, which is very suitable for indoor beautification. Small and medium-sized plants are often used to beautify the living room and study; medium and large plants are suitable for being arranged on both sides of the foyer of large buildings and in the center of the lobby, which is majestic and magnificent. It can reflect the tropical scenery, and rubber trees are commonly used for cutting and high-pressure propagation.

Cutting culture is relatively simple, easy to survive and grow fast. It is generally carried out in late spring and early summer combined with pruning. Select the middle branch of annual Lignification as cuttings, cut off the lower leaf with three buds, close the upper two leaves and tie them with plastic, or cut off half of the upper leaves to reduce water evaporation; in order to prevent the loss of too much milk from the cutting mouth and affect survival, the wound should be smeared with plant ash in time; the treated cuttings should be cut in a bed based on river sand or vermiculite. Keep the plug-in bed with high humidity after insertion, and often sprinkle water to the ground (but not stagnant water) to improve air humidity. Under the condition of 18 Mel 25 ℃ and semi-overcast, it can take root after 2 Mel for 3 weeks.

It is also convenient to use high pressure in the family, and the success rate is also high. Select biennial branches under high pressure, first peel 1 Mel 1.5 cm wide around the branches, then wrap them around the wound with wet moss or peat soil, and finally wrap them with plastic film and bind the upper and lower ends. 1 after 2 months, the rooting branches can be cut off and put on the basin.

 
0