The cuttage of the propagation method of drunken butterfly flower

drunken butterflies

Drunken butterfly flower is also called western white cauliflower, butterfly grass, purple dragon beard, native to tropical areas, popular in the world. The higher the plant, the flower is very similar to the dancing butterfly, and it is very beautiful under the sun. If you want to reproduce more drunken butterflies, you can adopt cutting propagation methods.

1. Cutting substrate

Is used for cuttage nutrient soil or river sand, clay and other materials. It is difficult to get ideal cuttage matrix due to family cuttage conditions. It is recommended to use cuttage matrix that has been prepared and disinfected; medium coarse river sand is also OK, but it should be washed several times with water before use. Sea sand and river sand in saline-alkali areas should not be used because they are not suitable for the growth of flowers and plants.

2. Selection of cuttings

The branches used for cuttings are called cuttings. Usually combined with the work of picking, the thick, disease-free top shoots taken off are used as cuttings, and the top shoots are directly used for cutting.

III. Management after cuttage

1. temperature

The optimum temperature for cuttings rooting was 18℃~25℃, lower than 18℃, cuttings rooting was difficult and slow, higher than 25℃, cuttings were easily infected and rotted, and the higher the temperature, the greater the proportion of rot. After cutting encounter low temperature, insulation measures are mainly used to cut the pot or container wrapped with film; cutting temperature is too high temperature, cooling measures are mainly to cut shade, to cover 50~80% of the sun, at the same time, to cut spray, 3~5 times a day, sunny temperature higher spray times are more, rainy days lower temperature is larger, spray times are less or not spray.

2. humidity

The relative humidity of the air must be maintained at 75 - 85% after cutting. The humidity can be increased by spraying cuttings 1 to 3 times a day. The higher the temperature in sunny days, the more the number of spraying times. The lower the temperature in rainy days, the less or no spraying times. However, excessive spraying, cuttings are easily infected and rotted by germs, because many kinds of germs exist in water.

3. illumination

Cuttage propagation can not be separated from sunlight, but the stronger the light, the higher the temperature in the cuttings, the more vigorous the transpiration of cuttings, the more water consumed, which is not conducive to the survival of cuttings. Therefore, after cuttage, the sun must be blocked by 50~80%. After the roots grow out, the shading net is gradually removed: the shading net is removed at 4:00 pm every day on a sunny day, and the shading net is covered before 9:00 am the next day.

How to cut the flowers, how to cut the flowers

In addition to sowing and breeding, drunken butterfly flower can also be propagated by cuttage. It is not difficult to operate drunken butterfly flower cuttage. The following methods and steps of drunken butterfly flower cuttage are arranged.

1. Soil preparation for cuttage

Drunken butterfly flower cuttage soil, generally can be mixed with nutrient soil or river sand, mud carbon soil, another cuttage soil must do disinfection treatment,

2. Branch selection

Drunken butterfly flower branch selection, general flower friends can pick the thick, disease-free top shoots as cuttings, directly with the top shoots cuttings.

3. Cutting method

Branches are selected, can be inserted directly into the prepared soil, and branches inserted, need to have a tight press, and then to keep the soil moist can be.

4. Maintenance after cuttage

Humidity control: After cutting, the relative humidity of the air must be maintained at 75~85%. Can spray to increase humidity, 1~3 times a day can be, if it is rainy days, the lower the temperature, the less or no spraying, to avoid cutting easy to be infected by bacteria and rot.

Light control: after cutting is inseparable from the light, but more than strong light, so after cutting must cover the sun 50~80%, after the root growth, and then gradually remove the shading net: sunny day 4:00 pm in addition to the shading net, the next day before 9:00 covered with shading net.

Temperature control: The suitable temperature for cutting rooting of Daphne incognita is 18℃~25℃. If the temperature is lower than 18℃, the cutting rooting is difficult and slow. If the temperature is higher than 25℃, the cutting is easy to be infected by bacteria and rot, and the higher the temperature, the greater the proportion of cutting rot.

How to breed drunk butterflies, and how to care for drunk butterflies after cutting

Drunken butterflies bloom in the evening and wither in the daytime the next day, so they are also called summer flowers. Their short life gives people a feeling of illusory impermanence. So how does the drunken butterfly flower cut and propagate? The following is a brief introduction to the nursing method after the cutting of drunken butterflies.

How to breed drunk butterflies, and how to care for drunk butterflies after cutting

Cuttage substrate: is used to cuttage nutrient soil or river sand, clay and other materials. It is difficult to get ideal cuttage matrix due to family cuttage conditions. It is recommended to use cuttage matrix that has been prepared and disinfected; medium coarse river sand is also OK, but it should be washed several times with water before use. Sea sand and river sand in saline-alkali areas should not be used because they are not suitable for the growth of flowers and plants.

The choice of cuttage branches: used for cuttage branches called cuttings. Usually combined with the work of picking, the thick, disease-free top shoots taken off are used as cuttings, and the top shoots are directly used for cutting.

Nursing methods after cutting of Drunken Butterfly Flower

Temperature: The optimum temperature for cuttings rooting is 18℃~25℃, below 18℃, cuttings rooting is difficult and slow; above 25℃, cuttings are easily infected by germs and rot, and the higher the temperature, the greater the proportion of rot. After cutting encounter low temperature, insulation measures are mainly used to cut the pot or container wrapped with film; cutting temperature is too high temperature, cooling measures are mainly to cut shade, to cover 50~80% of the sun, at the same time, to cut spray, 3~5 times a day, sunny temperature higher spray times are more, rainy days lower temperature is larger, spray times are less or not spray.

Humidity: After cutting, the relative humidity of the air must be maintained at 75~85%. The humidity can be increased by spraying cuttings 1 to 3 times a day. The higher the temperature in sunny days, the more the number of spraying times. The lower the temperature in rainy days, the less or no spraying times. However, excessive spraying, cuttings are easily infected and rotted by germs, because many kinds of germs exist in water.

Light: Cutting propagation can not be separated from sunlight, but the stronger the light, the higher the temperature in the cutting body, the more vigorous the transpiration of the cutting, the more water consumed, which is not conducive to the survival of the cutting. Therefore, after cuttage, the sun must be blocked by 50~80%. After the roots grow out, the shading net is gradually removed: the shading net is removed at 4:00 pm every day on a sunny day, and the shading net is covered before 9:00 am the next day.