MySheen

Clematis... Why do you buy it so expensive? Break it casually, and immediately change 1 basin into 1.

Published: 2024-11-22 Author: mysheen
Last Updated: 2024/11/22, Many flower lovers want to raise more expensive flowers, but they are cash-strapped and can't buy so many flowers. Today, Huahua will teach you how to change these precious flowers from 1 pot to 10 pots! Turn into a flower-growing tuhao in minutes!

Gentleman orchid

1. After the failure of the gentleman orchid, the seed pod will be produced, and after the seed pod turns reddish brown, the seed will mature. At this time, the seed pod will be cut off and the seed will be removed.

2. Soak the clean gauze in warm water, then wrap the seeds in the gauze and put them in a warmer place, preferably for 24 hours.

3. Spread sawdust in the seedling basin, spray it with water, put the soaked seeds tip down and put them in the sawdust.

4. Put the treated seeds in a place of astigmatism and spray water every morning and evening. After about 20 days, the seeds will sprout.

5. After the seed of Cymbidium grows a complete small leaf, it can be removed and planted in a flowerpot for maintenance.

6. After a period of maintenance, the magnolia has completed the transformation from seed to big seedling!

Orchid

1. Stop watering the orchid 1-2 weeks before the ramet, so that the root of the orchid becomes soft to avoid too much water and break at the ramet.

2. In most cases, the roots of orchids are entangled. It is necessary to separate the roots before ramet, otherwise it is easy to break a lot of roots.

3. Orchids are all planted one by one. Find the boundary between each plant and cut it along. In order to reduce the damage to the root, it is recommended that 3-5 plants should be separated as one, and then divided into a separate plant.

4. After dividing the plants, cut off all the dead roots, empty roots and weak roots of the orchid with sterilized scissors.

5. Soak the pruned orchid roots in carbendazim solution, disinfect them for about 30 minutes, then take them out to dry.

6. When disinfecting orchids, prepare several plastic bottles, cut off the waist, burn several holes in the bottle body and cap with red-hot wire, and cut a few triangular gaps in the cross section of the bottle.

7. Place the treated plastic bottle at the bottom of the flowerpot and fix it with a broken foam block, which can increase the air permeability and water permeability of the soil and avoid the rotten roots of orchids. Then put the prepared plant material into.

8. Put the divided orchids into the planting pots, so that one pot of orchids can become several pots!

Clematis clematis

1. Cut off the semi-lignified clematis branches, cut an oblique knife 3-5 cm below the node on each branch, cut a knife 0.5-1 cm above the bud point, and divide the branch into several small segments.

2. Prepare a clean foam board and poke several holes in the foam board with chopsticks, not too large in diameter.

3. Put a clematis branch in each foam board hole, and then put the foam board in clear water. In order to promote rooting, you can put a little rooting powder in the water.

4. Put the clematis cuttings in a cool and ventilated place to ensure that the roots are soaked in water. After about 20 days, fine roots can take root!

5. When the root system grows to more than 5 cm, it can be planted. Put a small amount of soil in the planting basin, put the clematis root plate, continue to fill the soil, can be properly mixed with a little slow-release fertilizer.

6. After planting, pour it with water mixed with carbendazim solution. Then keep it in a cool and ventilated place, and it can be maintained normally after a week.

Have you learned the reproduction of these precious flowers and plants?

If there are other breeding problems of flowers and plants

You can leave a message for Huahua.

 
0