A leaf makes ten pots of flowers. A leaf is bigger than a flowerpot. It's as simple as that.
Many flower friends in the maintenance of flowers, always inadvertently touch the leaves of flowers, naturally fell in the flowerpot do not care much. However, when I watered the flowers recently, I found a small bud growing. The editor is going to teach you today that you can get a pot of flowers by cutting plant leaves.
Money tree
Cutting steps
1. Choose a thriving cash tree, take a few leaves that grow well, take the petiole with you when picking, and then disinfect the wound with carbendazim.
2. Secondly, choose nutritious soil, which requires loose, fertile and good air permeability, and then cuttage its leaves.
3. Indoor, the cool and ventilated environment is the most suitable environment for flowerpots. It will take about two months to take root.
4. When the leaves produce new leaves, they should be put on the pot again, and some nitrogen fertilizer or compound fertilizer can be applied to increase the nutrients of the soil.
5. When watering, you should pay attention to watering after the soil is thoroughly dry; when the temperature is high, consider spraying some water. With its healthy survival, you can return to normal care.
Tiger Pilan
Cutting steps
1. Choose to intercept a section of tiger skin orchid leaves about 6CM, preferably those that grow vigorously, disinfect them with potassium permanganate solution, and then leave them in a cool place for a day.
2. Use loose soil mixed with sand and gravel, oblique or straight, about 5 cm. Remember to water thoroughly at this time.
3. Keep the soil moist and avoid excessive watering with appropriate amount of water. At the same time, remember to put it in a cool room is the most appropriate, good ventilation.
After the new bud grows, put it in a new basin and place it in an astigmatism place with good ventilation. At this time, the right amount of water can be watered, which must be less. In order to avoid stagnant water in the basin, resulting in rotting roots. ?
Longevity flower
Cutting steps
1. Cut the leaves of longevity flowers, preferably those with strong growth, and dry them in a cool and ventilated place.
2. Reconcile nutritious soil, coconut brick soil and perlite according to the proportion of 5:3:2
3. Then insert the leaves in the flowerpot, water the soil thoroughly at once, and maintain the indoor astigmatism.
4. Do not overwater after sprouting, otherwise it is easy to cause stem and leaf rot.
Epiphyllum
Cutting steps
1, the skill of cutting leaves: it is better to have old leaves more than two years old, about 20 centimeters is the best, put them in a cool place. The larger the wound area of the cut leaf, the easier it is to take root and grow.
2, leaf planting method: shallow or oblique insertion in the garden soil mixed with sand, the best depth is about two centimeters. As shown in the figure:
3. In order to keep the soil slightly moist after successful cutting, watering about twice a week is the most suitable. After waiting patiently for a month, it can take root and grow slowly.
3. Half a month later, the pot was carried out, and the soil around the leaves was connected to minimize the damage to the root system.
Sedum is succulent
Cutting steps
1. Select the succulent plants of Sedum with high success rate.
Choose healthy leaves, leave the growing point near the root, gently remove the leaves and let them dry in astigmatism.
2. Prepare the flowerpot and prepare the soil. Mix peat, vermiculite, rice husk ash and perlite according to the ratio of 1, 2, 1 and 1, and pay attention to soil moisture.
3. Cultivation methods: flat or oblique insertion, suitable depth and relatively stable. Put it in astigmatism.
4. Before the plant germinates, you can spray water into the air to keep it moist. After its growth is normal, you can move the basin and pour a small amount of water at the same time, not too much.
Have you learned the method of planting flowers mentioned above? Let's get moving!
- Prev
These eight kinds of flowers break branches and throw them into the water for 10 days to take root. It's too easy to feed.
These 8 kinds of flowers are very easy to reproduce, break a branch, throw them into the water, and take root in 10 days. It's so easy to feed. Let's take a look at which 8 kinds of flowers. Rubber tree is a flower potted plant that many people like. Its leaves are bright and glossy.
- Next
To preserve rose, jasmine and gardenia, you only need to bury some of this kind of flowering fertilizer to bloom one crop after another.
Many flower friends especially like gardenia, jasmine and rose, but what they fear most is that when the flowers bloom, the quantity is very small, which greatly reduces their viewing degree. Today, the flowers will introduce to you some tips to let these flowers burst into pots.
Related
- Wuhan Hospital Iron Tree Blooming Result Was Instantly Frightened by the Gardener Master
- Which variety of camellia is the most fragrant and best? Which one do you like best?
- What is the small blue coat, the breeding methods and matters needing attention of the succulent plant
- Dormancy time and maintenance management of succulent plants during dormancy
- Minas succulent how to raise, Minas succulent plant pictures
- What are the varieties of winter succulent plants
- How to raise succulent plants in twelve rolls? let's take a look at some experience of breeding twelve rolls.
- Attention should be paid to water control for succulent plants during dormant period (winter and summer)
- Watering experience of twelve rolls of succulent plants
- Techniques for fertilizing succulent plants. An article will let you know how to fertilize succulent plants.