He made a flower rack for delicious meat.

It's sunny

Ye Huimei

Jay Chou

00:00/04:29

BGM: Jay Chou-sunny day

Now, it is becoming more and more clear that meat friends are really omnipotent for meat.

Make pots for meat, paint basins, homemade shelves. It's all right!

Thanks to the author for his original sharing.

Edit and organize: succulent control

Coordinates: Taizhou

This time, I will introduce you how to design your own flower rack.

As a matter of fact, the flower rack has already been made, but some pictures have not been taken well, so it has been dragged on for a long time. The literary talent is limited, the design level is limited, there are bad places to do, please give us a lot of advice!

Preparatory work

Tools: angle iron, formwork, wood wax oil, metal paint, tricycle, mask gloves

Design: because the balcony is big enough, I made the flower rack a little bigger, around the size of the solid wood in the middle.

The plank is I help meat friends dig sand, she gave it to me, very strong, very good air gap.

I bought wood wax oil and brushed it all over the front and back. It's a good color.

The gap is not too small, the thumb basin will not fall, it is very comfortable.

Install & paint

The next step is to take the drawings to the steel market and ask master to weld them

It is 1.7 meters high and 1.5 meters long. The width is 0.9 meters.

If you want to be an editor, the first step is to die in drawing a design.

The angle iron used in the main body opens inward, with a plank on the top and jade dew on the bottom. In the end, it cost 400 dollars, and if you know the welder yourself, you can save more money.

After more than ten days, I finished welding and asked my neighbor to borrow a tricycle to bring back the iron frame.

When I brought it up, it almost got stuck on the stairs, and the width of the iron frame was just as wide as the stairs, so I had no choice but to move slowly.

When you draw your own dimensions, you must take into account the width of the door and corridor, otherwise it will be embarrassing if you can't get in.

The anti-rust bottom paint is ready!

The top paint is bright black, and black looks domineering.

Itself is to do murals, so the paint is easy to brush, three times, five out of two done, so just said that losers, after brushing, became rich and handsome, bright black really did not make a mistake.

The flower rack is separated, and the hollow iron pipe is welded at the dead corner.

Then put it on and secure it with a strap.

If a typhoon comes in summer, take it down in time.

When all is done, the film will be covered to increase the temperature difference.

Change the sunscreen and rain shield in summer.

I leave two vents in the lower left corner and the upper right corner. As soon as the sun temperature rises, the air inside will circulate by itself.

The size of the ventilation hole must be adjusted well, the temperature inside should not exceed 38 degrees when it is sunny in winter, put a thermometer, or feel it by hand, slightly hotter than the skin.

Such a film covering method, I test to increase the temperature difference is feasible, anti-frost drop at night has a certain effect, anti-cold wind has an effect. But there is no effect when the temperature is below-2 degrees in winter. The temperature is the same inside and outside.

PS: the main thing to do in summer is ventilation, and the area of the film has to be greatly reduced, as long as it is rainproof.

The upper layer is mainly Sedum varieties, thumb pots and so on.

At present, the bottom is still empty. Go back and buy some anticorrosive wood and put the jade dew leaves under it.

In this way, two floors can be used, which is higher than the space utilization rate of the staircase flower rack.

-production experience-

Cost: angle iron processing 400, wood wax oil, paint 200

It cost more than 700 to make this flower rack. I lent the tricycle to the neighbor two packs of cigarettes and the plank was free. After the whole thing is done, it does save some money, but it takes time.

A treasure flower rack of the same size is estimated to be more than 1000.

If you know a welding master, this 400 can be saved.

If you do it yourself, you must do it according to your own balcony.

My flower rack is for your reference only.

The four corners of the flower shelf must be reinforced with things to prevent windy weather.

Finally, of course, it is not that the flower racks sold are not good, but when some flower racks are designed.

Either the gap is too big to hold the flowerpot, or it is not sturdy without sense of security. I made it myself, and the things I use are stronger.

Finally, I put a few more beautiful pictures to miss the distant spring.

What things have you made for your own meat?

Leave a message and share it with you.