These things are placed in flowerpots and the plants have luxuriant green leaves and never rot their roots again.

What flower growers fear most is that the plants have stagnant water and rotten roots. once the roots of their own plants rot, despite the trouble of solving the problem, carelessness will probably make the plants die completely and have no room for revival.

The following editor recommends six kinds of good substrates for growing flowers. Using these six kinds of particles to grow flowers, the plants will have luxuriant green leaves and will never rot their roots again.

Coarse sand

Coarse sand has strong water permeability and remarkable drainage and air permeability, so it can be used to mix with other substances as a substrate for flower cultivation. For flowers that avoid stagnant water, coarse sand is undoubtedly a good choice for flower cultivation.

For example, in the maintenance of succulent plants, adding some coarse sand to the soil can play a good role in preventing excessive stagnant water in the basin and root rot, thus protecting the healthy growth of flowers.

How to use it:

After the sand is washed and fully dried, pass through the sand with a sieve. The larger particles can be mixed in the flower-growing soil, which can be used as the bottom soil in the flower pot.

Coal cinder

Cinder contains many small vents, which can further improve the permeability and drainage of soil; and cinder contains a lot of trace elements, which are very beneficial to plant growth and are a good choice for flower cultivation.

How to use it:

Select the completely burnt coal, then break it and sieve it to distinguish the large particles from the small ones. The larger particles are directly padded at the bottom of the flowerpot, and the thickness of the matrix is about 5 cm, which can further increase the air permeability of flowers.

The smaller particles can be mixed with the soil and can promote the healthy growth of plants.

Wood charcoal

Charcoal has loose texture, strong drainage and air permeability, and good moisture retention. Using charcoal as the substrate for flower cultivation can bring suitable temperature conditions and good humidity environment for plants, promote root respiration and accelerate the growth rate of flowers.

And charcoal also has the role of anticorrosion and disease prevention, can play a good role in preventing root rot and ulceration.

How to use it:

After repeatedly rinsing the charcoal with clean water, drying and sieving, removing sundries, disinfecting and sterilizing, select the larger particles, and mix charcoal, garden soil and pine needle soil at 1:2:2 to make the soil for flower life, and then plant plants in such a soil environment, you can speed up the growth of flowers.

Sawdust

When cultivating flowers, sawdust can be used to help increase the air permeability of the soil.

How to use it:

First of all, do not use fresh sawdust, you need to fully mature sawdust before starting to use, otherwise it is likely to have a negative impact on the growth of flowers.

You can soak the sawdust in boiling water for about an hour, then put it in a cool and well-ventilated place to dry, and then put the sawdust at the bottom of the flowerpot.

Broken brick and tile

Broken bricks and tiles can be said to exist like waste, but they can be used to grow flowers. Put some broken bricks and tiles at the bottom of the flowerpot, which can not only breathable and drain, but also moisturize and keep fat, with good health care effect.

How to use it:

Break the broken bricks and tiles, choose the small pieces with a diameter of about 0.5 cm, and put them at the bottom of the flowerpot when growing flowers. Just don't block the drainage hole. The smaller particles can be mixed with the garden soil to make the flower roots healthy and thrive.

Ceramic grain

There are many small air holes on the surface of ceramsite, which have good drainage and water retention. Using it to raise flowers can avoid root fester and improve the looseness and permeability of soil.

How to use it:

Using ceramsite to maintain succulent flesh or directly using ceramsite for hydroponic culture is a good choice. After washing ceramsite directly, it can be put into a container with a thickness of about 5 cm. It can be mixed with river sand and perlite, and the effect will be better.