These 5 kinds of flowers are not cutting now, and they will not bloom next year!

How to cut crab claw orchid?

1. Prepare the leaves of crab claw orchid that you accidentally touch. If you feel that a leaf is too few and do not look good in potted plants, you can cut off the top leaves of complete crab claw orchid. It is very energetic and easy to take root.

2. Put the leaves of crab claw orchid in a cool and ventilated place to dry for 1 or 2 days to allow the wound to heal.

3. Prepare soil. To cultivate the soil of crab claw orchid, we can use the mixture of pine needle soil and river sand at 1:1, which helps to maintain moisture and promote rooting.

4. The leaves of the dried crab claw orchid are stably inserted into the soil, compacted and watered thoroughly.

5. put a plastic bag on the coat of the flowerpot, increase the temperature in the pot, speed up the rooting, and then put the flowerpot in a place where the sun is not direct to wait for it to take root. You can check once every 3-4 days. If the soil is dry, spray some water with a spray can without watering it through.

6. After a week, the plastic bag can be removed. At this time, it will be found that the crab claw orchid has a tendency to take root, and after it sends out new buds, it can be managed normally.

7. The sprouted crab claw orchid seedlings were cultivated in pots to ensure sufficient growth space for the root system.

How to cut longevity flowers?

1. Use scissors to remove dynamic (especially flowering branches with more nutrients and higher rooting rate) longevity flower branches, about 6~7cm, each section should have two leaf nodes, and the extra leaves at the bottom can be cut off so that they can be inserted into the soil.

2. Prepare the soil. It can be mixed with rotten leaf soil and river sand at 1:1 to keep it moist.

3. The cut longevity flower branches should be put in a cool and ventilated place to dry before they can be used. Insert the dried longevity flower branches into the prepared basin soil, compacted and watered thoroughly.

4. keep the longevity flowers in a place where the sun is not in direct sunlight and take root two weeks later.

5. It should be noted that the succulent stem of longevity flower has a good water retention capacity, do not overwater during the period of germination, usually water once every 5-7 days, otherwise it is easy to rot.

How to cuttage rose?

1. Spring is a good season for cutting rose. Tilt 45 degrees to cut off well-developed, disease-free rose branches, 10cm or so, make sure there are two leaves on it, and the extra leaves can be removed. Be careful not to prick your hands when cutting.

2. Cultivate the soil of rose with sandy soil. After the soil is thoroughly watered, insert the rose and cultivate the flowerpot in a place where the sun does not shine directly to keep the sand moist.

3. The cutting rose branches will take root in about 15 days. At that time, the rooted rose seedlings will be moved into a larger flowerpot. It can be watered once a week in spring, because it is easy to rot if you water too much.

How to cut hydrangea?

1. Select semi-lignified branches, cut off about 10 cm, ensure that there are two leaves, the upper end is flat-cut, and the lower end is tilted 45 degrees.

2. Cut off the leaves by 1/2, which will reduce the evaporation of water and the acquisition of nutrients in the leaves, so that the nutrients are mainly concentrated in rooting and sprouting, and the smaller leaves can be cut less.

3, cultivate hydrangea soil with peat soil, add some vermiculite, pour through water, and then insert hydrangea branches into the soil. You can put a tray at the bottom of the basin and add some water to keep the basin soil moist in the process of cutting and promote rooting.

4. Pay attention to putting the flowerpot in a cool and ventilated place. At the present temperature, Hydrangea branches can take root in about 20 days.

5. After taking root, we move the hydrangea seedlings to a larger flowerpot and keep them in a place where the sun is not in direct sunlight.

How to cut triangular plum?

1. Prepare about ten centimeters of triangular plum branches, try to choose the more mature ones that have been lignified, and keep 2-3 leaves.

2. The soil can be prepared with rotten leaf soil and river sand at 1:1. After watering thoroughly, the triangular plum branches are inserted into the soil and placed in a place where the sun is not direct and ventilated. You can put on a plastic bag to keep moisture and speed up rooting.

3. When cutting triangular plums in spring, half of them will take root in about 20 days.

4. Transplant the new seedlings of Prunus mume which have already taken root into the pot and maintain them normally.

All right, Huahua, that's all for you today.

Flower friends can try it themselves.

Take advantage of the good spring, let's move!