Cut a branch at will, throw it in water for 3 days to take root, 20L flower pot can not fit!

Gardenia jasminoides root in water

When spring comes, it's time for gardenia to grow again, and cutting is the easiest time to take root at this time, so why not try it quickly?

Water insertion steps:

1. Prepare a large cola bottle, cut 1 knife from the top half of the bottle with scissors, be careful not to cut it completely, just leave part on one side.

2. Prepare the branches of Gardenia for cutting. It is best to choose a sturdy semi-lignified branch with a length of about 7-10cm, with 1-2 leaves on the branch and 45 °oblique cut at the bottom.

3. Prepare a foam board, cut the foam board into the same circle as the Coke bottle with scissors, probably a little smaller than the diameter of the Coke bottle, and then insert the branches that need to be cut into the foam board.

4. Put the foam board into the cola bottle, add water, and soak the lower end of the gardenia branches in water. Because the foam board will float on the surface of the water, the leaves will not rot. Finally, seal the opening of the bottle with duct tape, cover the bottle cap, and poke several holes in the bottle cap for ventilation.

5. Put the cola bottle in the place where the indoor solar energy shines, and the gardenia leaves in the bottle will carry out photosynthesis to promote rooting. If more water droplets are produced on the inner wall of the bottle, it is proved that the higher the temperature in the bottle, the faster it will take root.

6. It only takes 7-10 days for the gardenia cut in the cola bottle to produce the root system of the white flower.

Triangular plum water cuttings take root

Triangular plum has a variety of colors, blooming for more than half a year, and if it can be grafted, it is even more colorful and beautiful!

Water insertion steps:

1. Buy some transparent acrylic tubes and cut them into small pieces about 7-10cm in length with a knife.

2. Prepare the robust triangular plum branch, peel off the outer skin of the lower end of the 2cm, which can prevent rotten skin, and then wrap the cut non-woven cloth around the branch, and one end of the cloth can be flush with the lower end of the branch.

3. Insert the triangular plum branches together with the non-woven cloth into the plexiglass tube, which can not only ensure the moisture and air permeability of the branches, but also prevent the cuttings from rotting.

4. Prepare a plastic plate, add 2cm water to the plastic plate, add some rooting powder and stir, then put the triangular plum cuttings in.

5. In about 5-7 days, there will be a lot of small white spots at the bottom of the triangular plum cuttings. At this time, you can prepare to put on the basin, or you can wait for the small white spot to emerge and become a root system before going on the basin.

6. Cut the napkin into strips, wet it with water and start winding the wrapping branches from the root. Wrapping branches with toilet paper can temporarily isolate the contact between organic matter in the soil and tender roots during cutting, which is more conducive to rooting.

7. Cutting soil can prepare perlite, vermiculite and peat soil. Cut the plastic bottle, burn 3-5 holes evenly at the bottom, then pad the vermiculite at the bottom, and then fill the plastic bottle with a mixture of peat and perlite.

8. Put the triangular plum branches into the nutritious soil of the plastic bottle, cover the seedlings with the top of the plastic bottle, water them once and place them on the sunny windowsill. In less than a month, you can see the root system of the triangular plum coming out from the bottom of the plastic bottle.

9. Cut the plastic bottle with scissors, try not to scatter the soil carried by the root system, then transplant it into a larger flowerpot, place it in a cool and ventilated place for a week, and then put it directly in the sun.

Green apple water is inserted to take root.

Recently, the flower pruning green apple, leaving a lot of branches, these branches can take root when thrown into the water, and soon become a new pot of green apple!

Water insertion steps:

1. Choose those strong green radish branches, and then cut the branches into small segments of about 5-7cm.

2. Prepare a small bottle of water, the water level is about 2 beat 3 of the bottle, then insert the lower end of the branch into the water and put it in a place where the scattered light is bright.

3. It only takes about a week or so for the green apple to sprout a small root.

4. After rooting, the green pineapple can continue to be preserved in the bottle, or you can prepare loose and breathable nutrient soil. Transplanting the rooted green turnip into the flowerpot for soil culture can make the green turnip rub long!

Longevity flowers take root by water insertion

The longevity of many flower friends' families has recently reached the time of failure. Don't lose the branches you cut while pruning. Just put water into them and turn them into a new pot of longevity flowers every minute!

Water insertion steps:

1. Prune the branches of longevity flowers, select the sturdy ones and trim them a little. Leave 2-3 leaves on each insert.

2. Soak the longevity flower branches in rooting water for about 20 minutes, dry them into clear water, dip the lower end of the branches with a little water, and then put them in a place with good scattered light for maintenance.

3. It only takes 7-10 days for longevity flowers to grow white roots.

4. After taking root, you can choose to continue to maintain it in a hydroponic bottle to watch the white roots, or you can transfer it directly to the soil culture in the flowerpot, which will soon burst the pot!

That's all for Huahua today!

What other flower cuttings do you want to see?

Why don't you leave a message for Huahua?