How to plant the seeds of the latest asparagus?

Do you know how to plant seeds of asparagus? Wenzhu is an ornamental plant with extremely high height. It likes warm, humid and semi-shady ventilation environment. It can be placed in living room and study room. It can purify the air and also add the smell of books. In the process of cultivation, seeds can be used for reproduction. The following small series will introduce how to plant seeds of Wenzhu!

How to plant bamboo seeds?

Some of the seeds of asparagus are purchased directly, some are harvested by themselves. The fruits of asparagus ripen one after another in winter. When the fruits of asparagus turn purple and black, seeds can be collected. After the fruits are collected, peel off the pericarp and take out the seeds. After washing, they can be sown.

The temperature of asparagus germination needs to be above 18℃. If the temperature does not reach it, the sowing time can be postponed. The sowing medium of asparagus is relatively free. It can be used for seedling block, peat sowing, or garden soil + honeycomb coal. However, it is suggested that the sowing medium can be selected as far as possible with good permeability.

Do not sow asparagus soil too deep, generally about 2 cm can be, and then pay attention to moisture, can cover the film or with a seedling box, placed in a sunny place, to maintain the temperature above 18℃, for germination time, to have patience, according to understanding, some flower friends sow 2 weeks to germinate, there are 3-4 weeks to germinate, so the key to sowing is to have patience. After germination, when the seedlings grow to 3~ 4 cm high, they can be transplanted.

Reasons for non-germination of asparagus seeds after sowing

1. The seeds are not ripe before picking, and it is difficult to germinate after sowing. Harvesting should generally wait for its seed shell is purple black soft re-harvest, and timely scrub peeling, floating to empty shriveled seeds.

2. Seeds are not soaked for 24 hours before sowing or the soil in the sowing basin is too dry, and it is difficult for seeds to germinate.

3. The room temperature when sowing is too low. When the temperature is lower than 10℃, the seeds are not easy to germinate.

4. The soil in the basin is too wet and sticky, and the seeds rot after the crack is exposed, resulting in failure to germinate.

The old seeds themselves have long lost their vitality.

Bonsai Making after Germination of Phyllostachys glaucus Seeds

Wenzhu posture beautiful, branches fine soft, layered, high and low order, after the design composition made of bonsai furnishings balcony or indoor, more beautiful and quiet, its production method is as follows:

1. Material selection: one bamboo about 20cm high, two bamboo more than 10cm high, irregular white marble shallow basin and several supporting frames, a number of rocks about 10cm high, proper amount of cultivated soil and moss.

2. Bonsai modeling: spread a thin layer of culture soil on the shallow pot surface of white marble, plant the tallest asparagus and curved branches and leaves to the right end of the pot to the left, plant the second height asparagus not far from the left side of the first asparagus at the appropriate position near the back edge of the pot, and then plant the shortest asparagus at the junction of 1/3 and 2/3 of the pot length, and the curved branches and leaves of asparagus should also be to the left to achieve the coordination and unification of the orientation of the three asparagus. Then adjust the position of asparagus in the basin to achieve natural beauty.

3, point stone spread moss: put a number of rocks on the right rear position of the basin surface, and cover moss on the cultivation soil of the basin surface to achieve the artistic effect of greening. Finally, spray water on asparagus and moss to moisten the culture soil.

Method for shaping bonsai of asparagus

1, pot control method: the size ratio of flower pots and plants should be 1:3, so that the growth of roots can be limited, keep the plant size unchanged.

2. Remove the growth point: When the new bud grows to 2~3cm, remove the growth point, which can promote the regeneration of branches and leaves on the stem, and can control its long vine, so that the branches and leaves are flat and the plant shape is constantly plump.

3, the use of bamboo phototaxis: timely rotation of the direction of the flowerpot, can correct the growth shape of branches and leaves, keep the plant type unchanged.

4, the object cover method: that is, use hard paper to press the branches and leaves or cover the sun, so that when the branches and leaves grow, they touch the object to block the stem or bend the growth, thus achieving the purpose of modeling.