MySheen

What matters should be paid attention to in the use of the flip plow? How to repair and maintain?

Published: 2024-11-24 Author: mysheen
Last Updated: 2024/11/24, In northern China, the traditional tillage method has been used for a long time: ploughing with moldboard ploughing, the ploughing depth is generally in 25~30cm. In the long run, the thickness of the plough bottom increases and the water storage capacity of the soil weakens, so that the moisture in the soil cannot be preserved to the maximum extent.

In northern China, the traditional tillage method has been used for a long time: ploughing with moldboard ploughing, the ploughing depth is generally in 25~30cm. In the long run, the thickness of the plough bottom increases and the soil water storage capacity weakens, so that the water in the soil can not be preserved and utilized to the maximum extent, which affects the yield and harvest of crops. The emergence of the turning plow easily solves this problem and replaces the moldboard plough. once the turning plow enters the ground, the soil within the working width can be turned over within the normal ploughing depth and the soil at the bottom of the plough can be loosened up and down. the requirement of deep ploughing without disturbing the soil layer. The test results show that the prototype reaches the design index and has wide application value. So what matters should be paid attention to in the use of the flip plow? How to repair and maintain?

Matters needing attention in the use of overturning plough

In the process of using the turning plow, we should pay attention to the consistency of the ploughing depth, and achieve the function of turning deeply and breaking the bottom of the plow. In order to meet the requirements, the turning plow often has to do an in-depth investigation before the operation, and a comprehensive and effective inspection of the machinery itself is a kind of protection for the operation of the machinery itself.

1. The overturning plough must have special personnel responsible for maintenance and use, be familiar with the performance of the subsoiling machine, and understand the structure of the machine and the adjustment method and use of each operating point.

2. Before turning the plough, the connecting bolts of each part must be checked and there must be no loosening. Check all parts of the grease, not enough should be added in time, check the wear of vulnerable parts

3. In ploughing operation, the distance between deep loosening should be kept consistent. The operation should keep driving at a uniform speed and in a straight line.

4. No heavy loosening, no leakage and no hauling should be ensured during the operation.

5. During the operation, the operation should be checked at any time, and the blockage of the machine should be cleaned up in time.

6. If there is an abnormal noise during the operation of the overturning plough, the operation should be stopped in time, and the operation should be continued after the cause has been found out.

7. when the machine is working, when there is a surge of hardness and resistance, please stop the operation immediately, eliminate the bad condition, and then carry on the operation.

8. in order to ensure the service life of the overturning plow, the machine should be carried out slowly when it is buried and unearthed, and it should not be forced to operate.

9. When the equipment is in operation for a period of time, a comprehensive inspection shall be carried out and the faults shall be repaired in time.

After the turning plow has been adjusted on one side, the other side should be adjusted in the same way in order to achieve the effect of consistent left and right ploughing depth. This requires us to patiently and meticulously do a good job of preparation before homework, as far as possible to grasp the efficiency of the use of the overturning plow.

Maintenance, maintenance and troubleshooting of overturning plough

1. Check the forbidden degree of all bolts and nuts regularly.

2. Ensure that the plough side plate is in good condition, and the worn side plate will affect the working performance of the plough. the side plate of this series of plough can be used interchangeably and turn over the plow with constant force, so as to improve the service life of the plow.

3. The worn parts may affect all aspects of the performance of the plough, so it is necessary to check and adjust all parts of the plough body frequently.

4. Add lubricating oil to each lubrication point every 8 hours, especially to ensure the rotation flexibility between the rotating shaft of the plow frame and the suspension frame.

5. Hydraulic components should pay attention to dustproof, moldboard overturning plough, anti-turbidity, cylinder piston rod should pay attention to bumping. In the long-term placement, pay attention to the pipe joint tightly sealed.

6. The pneumatic overturning structure must be disassembled, cleaned and filled with lubricating oil or grease before or after operation to keep it in good condition.

7. In the process of transportation or progress, the plough must be turned over and slow down when passing through rough roads or ridges, so as to avoid mechanical damage caused by excessive bumpy impact.

 
0