How to cultivate succulent Phyllostachys pubescens and its Culture methods and points for attention

It must have attracted the attention of many people for the cute and fleshy appearance of Zaolingyu. It looks round and plump, and it is very suitable for breeding on the table and on the desk. Flower friends all know that succulent plants are actually relatively easy to raise, and the right temperature and light can make succulent plants thrive. So what else should we pay attention to in the breeding of algal bell jade? Let's take a look.

How to raise succulent algal bell jade

1. Prepare before sowing

The matrix formula is to mix peat with small particles of deer marsh soil (12 mm) at 5:1 and set aside. In order to prevent the soil from carrying weed seeds and harmful bacteria, it is necessary to disinfect them. In order to prevent killing all the beneficial bacteria in the soil and affecting the normal growth of seedlings, the concentration of potassium permanganate solution should not be too high and the solution should be dark pink. The next morning, the basin soil has been soaked by potassium permanganate solution, will be out of the pot to dry, to noon to sow seeds.

2. Sowing seeds

Water the pot soil thoroughly before sowing. The seed of algal bell jade is very small, pour it on the white paper, fold the white paper horizontally, make the paper slot face the basin, and gently tap the paper slot with the camera to make the seed slide evenly to the surface of the soil. Do not cover the soil after sowing, spray carefully with 1000 times carbendazim water until the bottom of the basin leaks. When spraying, the water mist should be fine and the action should be light to prevent the seeds from being sprayed into the soil. After that, cover the spinach with cling film in the sowing pot and put it in a place with plenty of light. 3. Management after sowing

After sowing, open a small crack in the plastic film every day, ventilate for about 2 hours, spray some water and then cover it. In order to prevent the growth of bacteria caused by high humidity, fungicides are sprayed every 3 days. 1000 times carbendazim and chlorothalonil can be sprayed alternately to prevent bacteria from developing drug resistance.

Seven days later, the seedlings sprouted. After budding, the cling film is gradually lifted to give sufficient light to the seedlings to prevent overgrowth. One and a half months later, Xiao Miao began to molt for the first time. At this time, the water should be strictly controlled, and the basin soil can be humidified with a small amount of spray when the soil is too dry.

Culture methods and matters needing attention of Phyllostachys pubescens

I. the culture method of algal bell jade

1. Lighting

Like the warm, sunny environment, drought-resistant and cold-resistant, so be sure to remember to put the algal bell jade in the sunny place!

2. Moisture

The plant is dry and watered without soaking in the basin. The whole summer sunshade, put in the bright and ventilated scattered light, summer will also give a small amount of water, more will rot. The water supply can be restored after the autumn temperature comes down, step by step. If the plant is full, it does not need to be hydrated. If you find that the leaves are a little weak, you can replenish the water immediately.

3. Soil

Like fertile soil with good drainage, choose rotten leaf soil plus garden soil plus granular soil or coarse sand and other mixed plants. You can also use cinder mixed with a small amount of peat, and then mixed with a small amount of red jade soil and blue stone, the surface covered with granular river sand. Plant materials should be permeable and air-permeable.

4. Temperature

The suitable growth temperature is 24 degrees 18m / m / m.

5. Reproduction

The reproduction of Phyllostachys pubescens can be sown or ramets.

II. Matters needing attention in the culture of algal bell jade

1. Summer

High temperature will make algal bell jade dormant, so we should pay attention to shading and ventilation.

2. Winter

The temperature should be kept above 10 degrees. If the heating is good, the water can be watered appropriately, otherwise the water will be cut off.

The reason for the rotting root of algal bell jade

The main results are as follows: 1. To a certain extent, the rotten root of algal bell jade is caused by too much watering. If the water is too much, it can not flow out or evaporate in time, which will cause plant root hypoxia and rot to a certain extent. Or root rot caused by too much fertilization.

2. A single soil can also cause decay. If the soil is breathable, the excess water will flow down and will not cause flooding, especially in the rainy summer season.

Treatment method of rotten root of algal bell jade

The first step: pull out all the algal bell jade, clean the roots, and then cut off all the moldy parts, remember to cut them all, leaving nothing at all!

Step 2: carefully apply carbendazim to the wound and then dry it for about three days.

Step 3: re-root the dried algal lily jade. There are many ways to root it. You can hang it at the mouth of the bottle and put water below without touching the root. You can also replant it in the granular soil to let it take root slowly.

Step 4: put the algal bell jade planted or at the mouth of the bottle in an indoor place with plenty of light, but be careful not to be exposed to direct sunlight, but also pay attention to indoor ventilation. Wait for the algal bell jade to take root and then water it step by step. Don't water it at the beginning. In one to three weeks, the algal bell jade will root and grow again.

The above is the whole content of how to raise algal bell jade, in fact, it is very simple, everyone come and raise a lovely pot of algal bell jade. However, it should be noted that in summer, you can often loosen the soil and put it in a ventilated place to avoid stagnant water causing rotten roots.