MySheen

How to Propagate Milan Flower methods of Aquatic Culture

Published: 2024-11-23 Author: mysheen
Last Updated: 2024/11/23, The way plants reproduce determines whether plants can grow and survive widely. Most endangered species are due to difficulties in reproduction. To be honest, this is also a kind of natural selection. Milan is relatively common in the world.

The way plants reproduce determines whether plants can grow and survive widely. Most endangered species are due to difficulties in reproduction. To be honest, this is also a kind of natural selection. Milan, as a relatively common species in the world, should have many ways of reproduction.

How do Milan flowers reproduce?

1. Cuttage propagation

Cuttings can be cut with hardwood or cuttings.

1. Hardwood cuttings need to choose one-to two-year-old branches of Milan as cuttings, cutting the cuttings into several segments, each of which is about 8-10 cm in length, which will be carried out in April and May.

For cuttings, it is necessary to choose the semi-lignified branches of the same year, and the length of cuttings is 10 cm. Plain sand, peat soil or perlite can be used as cutting substrate.

2. When cutting, you should first make holes in the substrate, and then insert the cuttings into the cuttings. To make the cuttings combine closely with the substrate, you can press them gently with your hands. After watering, shade maintenance is carried out.

2. Striping propagation

Striping reproduction can be carried out from May to September, and it is best to choose the time in the rainy season, when the survival rate is relatively high. The high-voltage method is mainly used for pressing.

1. Preparation before high pressure: fertilize and irrigate Milanshu in the first 20 days of high pressure to make the plant grow healthily and exuberantly. Prepare appropriate amount of binding rope, moss, ring peeling knife or grafting knife, plastic microfilm strips, branch shears and syringes.

2. High-pressure technology: ① soaks the moss in water for an hour, then takes it out. ② selected the healthy plant and peeled it around the branch, and at the same time gently scraped the cambium with the grafting knife to break it, in order to make the new plant take root. ③ wrapped the moss in a plastic microfilm and tied it in a ring peeling mouth.

3. Tending and management after high pressure: strengthening fertilizer and water management, fertilizing and watering in time. Carry out pest control and spray specific pesticides for pest control in a timely manner. After the root system of the new plant grows, the plant with good growth can be selected for pruning and transplanting.

Methods of hydroponic Culture of Milan Flower

I. selection of plants

If you want hydroponic culture, you must first select suitable plants for hydroponic culture, and choose healthy and well-growing branches for hydroponic culture, which can increase the probability of successful operation.

2. Equipment preparation

Scissors or sharp knives, foam plates, potassium permanganate and other disinfectants, mineral water bottles, tape and so on.

III. Method of operation

1. Disinfect the scissors or carving knives and trim the lower end of the Milan branches. It is best to cut obliquely to increase the contact area of the oblique section.

2. Disinfect the treated wound and wait for it to dry naturally.

3. Put the mineral water bottle on the foam board prepared in advance, and cut the foam board according to the bottom of the mineral water bottle.

4. Pass the prepared Milan branches through the foam board. It is best not to plant too many plants on a foam board to ensure a certain distance.

5. cut the mineral water bottle from the waist in the middle. Don't separate it all. It's best to leave a little bit to keep it implicated. It is filled with the right amount of water.

6. Place the foam board with Milan branches in the mineral water bottle and fix it. Then rejoin the upper part of the mineral water bottle with the lower part and seal it with duct tape.

IV. matters needing attention

Hydroponic Milan should remember to change water regularly and make sure the water quality is clean. in addition, just hydroponic Milan, there may be the phenomenon of yellow leaves and rotten leaves withering in a few days. At this time, as long as the yellow leaves are pruned off in time, some small white spots will emerge one after another under the slow plant, do not think that it is moldy, that is a normal phenomenon, is a sign of Milan's growth. In addition, don't throw away the blackened leaves, patience and so on will be successful. after seeing the small roots growing below, just move them to the hydroponic container and add the nutrient solution.

When will the Milan blossom

Milan is a plant with a long flowering period, which blossoms from July to August, or in all seasons.

Milan flower is more characteristic, axillary panicle, yellow flowers, very fragrant.

Is Milan poisonous?

Milan is not poisonous. Many people will have a lot of concerns about farmed flowers and plants, but science has proved that Milan flowers are not poisonous. On the contrary, Milan flower has many effects, all of which are beneficial to people. So there is no need to worry about this problem.

Milan can reproduce either by cutting or by pressing strips, each of which has its own advantages and advantages. Milan is also a kind of plant capable of hydroponic culture. through hydroponics, we can better watch the whole process of growth and development of Milan.

 
0